How do you mark in SolidWorks?

What is center Mark in SolidWorks?

Center marks are annotations that mark circle or arc centers and describe the geometry size on the drawing. With the Center Mark tool, you can create a center mark or a center point on circular edges. The center mark lines can be used as references for dimensioning.

How do you annotate a slot in SolidWorks?

Manually Placing Sketch Slot Center Marks

1. Click Center Mark (Annotations toolbar).
2. Under Manual Insert Options, select Slot center mark.
3. Select other options for the center mark type.
4. In the graphics area, select an arc or curved edge of a slot and click .

How do you use symbols in SolidWorks?

To add symbols from the Microsoft Character Map:

1. Click Character Map.
2. In the Character Map, click a symbol and click Select to add it to the Characters to copy field.
3. When you have added the characters you want, click Copy.
4. Close the Character Map.
5. Paste the characters into the Symbols to insert field.

How do you use the line command in SolidWorks?

You can activate the 2D Command Line Emulator by clicking Tools > Add-Ins and selecting SolidWorks 2D Emulator from the list of add-ins. The command line appears at the bottom of the screen when you open a document. To turn off the emulator, click Tools > Add-Ins , and clear the SolidWorks 2D Emulator check box.

How do you draw a circle in Solidworks?

Circles

1. Sketch tab. Click the Sketch CommandManager to select circle tools from the Circle. flyout tool.
2. Menu. Click Tools > Sketch Entities to select circle tools.
3. Circle PropertyManager. Change to different circle tools from the Circle PropertyManager.

How do I draw a center line in a circle in Solidworks?

To create a centerline:

1. Click Centerline. (Sketch toolbar) or click Tools > Sketch Entities > Centerline.
2. Click to start the centerline.
3. Drag, or move the pointer and click, to set the end of the centerline.

How do you write slot dimensions?

Slots are dimensioned by giving their overall dimensions. Or, by giving the overall width and the distance between centers.

How do you make a curved slot in SolidWorks?

In a sketch, click 3 Point Arc Slot (Sketch toolbar) or Tools > Sketch Entities > 3 Point Arc Slot . Click to specify the starting point of the arc. Move the pointer to specify the ending point of the arc and then click. Move the pointer to specify the third point for the arc and then click.

Where is the symbol library in Solidworks?

Click Options. (Standard toolbar) or Tools > Options. On the System Options tab, click File Locations. Under Show folder for, select Symbol Library File.

How do you use special characters in Solidworks?

How To Insert Special Characters in SOLIDWORKS

1. Make sure your keyboard is in NumLock mode.
2. Hold down the ALT key and enter the number on the numeric keypad. (Note that many laptops have a blue FN key that changes a set of keys, also with blue numbers on them, into a numeric keypad.)

How do you draw a third angle projection symbol in solidworks?

Click on “Note” and select “Add Symbol” as indicated in the red box below. Under “Symbol library”, select “Projection Symbol”. Select “Third Angle Projection” and click OK. Left-click on the drawing sheet to place the projection symbol.

How do you draw a line in Solidworks?

To sketch a line:

1. Click Line. …
2. In the Insert Line PropertyManager under Orientation, select one of the following: …
3. Under Options, select: …
4. Under Parameters, you can do the following, based on the Orientation: …
5. Click in the graphics area and sketch the line. …
6. Complete the line in one of the following ways:

How do you draw a reference line in Solidworks?

1) Command manager: Feature > select reference geometry > Plane. 2) OR Menu: Insert > Reference Geometry > Plane. Plane at offset Distance: If we want to draw a new sketch at some distance of part it needs new plane.

How do you draw a vertical line in Solidworks?

on the Sketch toolbar, or click Tools > Sketch Entities > Line.

…

In the Insert Line PropertyManager under Orientation, select one of the following:

1. As sketched.
2. Horizontal.
3. Vertical.
4. Angle.