You asked: How do you delete a draft in Solidworks?

What does draft do in Solidworks?

Draft tapers faces using a specified angle to selected faces in the model. One application is to make a molded part easier to remove from the mold. You can insert a draft in an existing part or draft while extruding a feature.

How do I find a draft in Solidworks?

To perform an analysis:

  1. Click Draft Analysis (Mold Tools toolbar) or View > Display > Draft Analysis . Set analysis parameters and color settings, and then click .
  2. Click View > Modify > Draft Analysis.
  3. Click Draft Analysis (View toolbar) or View > Display > Draft Analysis.

What is step draft?

A step draft is a variation of a parting line draft. The step draft creates one face rotated about the plane used as the Direction of Pull. This results in small faces, representing the steps (highlighted in blue in the example below).

How do I use draft expert in Solidworks?

To access the DraftXpert: Click Draft (Features toolbar) or Insert > Features > Draft.


  1. Create multiple drafts.
  2. Create multiple drafts.
  3. Create multiple drafts.
  4. Automatically invoke the FeatureXpert to resolve draft features that do not initially go into the model easily.
IT IS INTERESTING:  Question: What is the function of block command in AutoCAD?

How do you remove the draft angle in SolidWorks?

Set a value for Draft Angle and click Change to modify the draft for the selected faces. In this example, change the draft to 10deg . Under Draft Analysis, select Auto paint to see what other faces need draft. To remove draft from faces, you would click Remove.

What is draft in injection molding?

A draft angle is calculated as a degree measurement (or, less often, an inch or millimeter measurement) from the vertical axis of a mold, and it helps account for thermoplastic shrinkage, a practical reality of the injection molding process for most materials.

What is draft analysis?

The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values.

How do you add a draft angle in Solidworks?

To insert a draft angle parting line:

  1. Sketch the part to be drafted.
  2. Insert a split line curve, if desired.
  3. Click Draft on the Features toolbar or click Insert > Features > Draft.
  4. Under Type of Draft, select Parting Line. …
  5. Under Draft Angle, enter the Draft angle .

How do I do a draft analysis in Catia V5?

How to do draft analysis in Catia V5

  1. enter part in Catia.
  2. Go to Material Mode.
  3. 03.go for draft analysis.
  4. drag axis bar to the tooling direction of part.
  5. check for draft and make parting line as per analysis. Was this tutorial useful? Like.
  6. 4 likes.
IT IS INTERESTING:  Your question: How do i mirror text in autocad without mirroring?

What is neutral plane in Solidworks?

You can create a feature that tapers selected model faces by a specified angle, using a Neutral Plane to determine the direction of pull for creating molds. You can also use the DraftXpert to create, change, or remove neutral plane drafts.

What is a stepped parting line?

Stepped Parting Line

For this type of parting line, there’s usually a large force on one side of the cavity. This causes a relative possibility of sliding between the fixed and moving halves of the mold. This force can then be canceled out by generating an injection force on both sides of the cavity.

What is the application of draft feature?

About the Draft Feature. The Draft feature adds a draft angle from -89.9° to +89.9° to individual surfaces or to a series of surfaces. You can draft only the surfaces that are formed by tabulated cylinders or planes. To access the Draft feature, click Model > Draft.

What is loft in Solidworks?

Loft creates a feature by making transitions between profiles. A loft can be a base, boss, cut, or surface. You create a loft using two or more profiles. Only the first, last, or first and last profiles can be points.

Special Project