Question: How do I extend a curve in SolidWorks?

How do you extend a shape in Solidworks?

Extend Surface

1. Click Extended Surface (Surfaces toolbar) or Insert > Surface > Extend.
2. In the PropertyManager: Under Edges/Faces to Extend, select one or more edges or faces in the graphics area for Selected Face/Edges . For edges, the surface extends along the plane of the edge. …
3. Click .

How do I extend a center line in Solidworks?

You can add to the length of a sketch entity (line, centerline, or arc). Use Extend Entities to extend a sketch entity to meet another sketch entity. on the Sketch toolbar, or click Tools > Sketch Tools > Extend. Move the pointer over the sketch entity to extend.

How do you move a curve in Solidworks?

To move or copy entities:

1. In sketch mode, do one of the following: Click Move Entities. (Sketch toolbar) or Tools > Sketch Tools > Move. …
2. In the PropertyManager, under Entities to Move or Entities to Copy: Select sketch entities for Sketch item or annotations. …
3. Under Parameters: Sketch Type. …
4. Click .

How do you curve a straight line in Solidworks?

To autotransition between line and arc:

1. Click Line (Sketch toolbar) or click Tools, Sketch Entities, Line and sketch a line.
2. Click the endpoint of the line, then move the pointer away. …
3. Move the pointer back to the endpoint, then away again. …
4. Click to place the arc.
5. Move the pointer away from the arc endpoint.

How do I stretch a part in Solidworks?

Stretching Sketch Entities

1. Click Base point. and then click on the sketch to set a base point.
2. Drag to stretch the sketch entities. When you release, the entities stretch to that point and the PropertyManager closes.

How do you extend an extruded surface?

To extend or extrude the edge of a surface

Select the outside edge of a surface. Ctrl+click to select multiple edges. Click the Pull arrow oriented along the surface to extend the edge. Press Tab or click the other Pull arrow to extrude the edge in another direction.

What are extension lines?

Extension lines continue or extend from the surface of the object and establish the size of the dimension. They do not touch the object lines and extend slightly past the dimension line. Extension lines provide a means of displaying a measurement without placing the dimension on the part.

What is the gap between the extension line and the object you are dimensioning?

Extension Lines

There should be a gap of about 1 / 16″ where the extension line would meet the outline of the object, and the extension line should go beyond the outermost arrowhead approximately 1 /8″.

How do you draw a line extension?

When drawing an extension line, you should leave a 1/16-inch gap between the outline of an object and the beginning of an extension line. Extension lines will extend another 1/8-inch beyond the outermost dimension line.

How do you move a shape in SOLIDWORKS?

Click Move/Copy Bodies (Features toolbar) or Insert > Features > Move/Copy . Specify parameters to move, copy, or rotate bodies. Apply mates between bodies. Click Translate/Rotate or Constraints at the bottom of the PropertyManager (if necessary) to switch to the page you want.

How do you move a circle in SOLIDWORKS?

To modify a circle in an open sketch by dragging:

1. Increase the perimeter by dragging its edge away from its center point.
2. Decrease the perimeter by dragging its edge toward its center point.
3. Move the circle by dragging its center point.

How do you drag a figure in SOLIDWORKS?

Dragging

1. Select a view (the pointer changes to. ) and press Alt while dragging.
2. Select the edge of a view (the pointer changes to. ), then drag.

What is the file extension of a Solidworks drawing file?

When you save a file natively in SOLIDWORKS, it can be saved as an: SLDPRT part file (. sldprt) SLDASM assembly file (.

Can you change a line to an arc in Solidworks?

You can transition from sketching a line to sketching a tangent arc, and vice versa, without selecting the arc tool. (Sketch toolbar) or click Tools > Sketch Entities > Line and sketch a line.

How do you make an arch in Solidworks?

To sketch tangent arcs:

1. Click Tangent Arc .
2. Click. on the end point of a line, arc, ellipse, or spline.
3. Drag the arc to the desired shape and release. SOLIDWORKS infers from the pointer motion whether you want a tangent or normal arc. …
4. Click .