Frequent question: How do I read a static simulation in Solidworks?

How do I read SOLIDWORKS Simulation results?

Displaying SOLIDWORKS Simulation Results in the Graphics Area

  1. Open an assembly that has a simulation study saved with it.
  2. Click the Static 1 tab.
  3. In the Simulation Study tree, right click Static 1 and click Run.
  4. Click the Model tab.
  5. Click Simulation Display (View toolbar) or View > Display > Simulation Display .

How do I run a static Simulation in SOLIDWORKS?

To perform static analysis:

  1. Create a static study. …
  2. Define material for each solid, shell, and beam. …
  3. Define restraints. …
  4. Define external loads.
  5. For assemblies and multibody parts, use component contact and contact sets to simulate the behavior of the model.
  6. Mesh the model and run the study. …
  7. View the results:

What result plots SOLIDWORKS Simulation automatically creates upon completion of a static analysis?

When the analysis completes, SolidWorks Simulation automatically creates default result plots stored in the Results folder. Global element size is a measure of the average diameter of a sphere circumscribing the element.

How do you analyze in SOLIDWORKS?

To set up stress analysis on one or more components:

  1. Click Simulation Setup (MotionManager toolbar).
  2. In the graphics area, select a component on which to perform the stress analysis. …
  3. Enter the Start Time and End Time for the analysis. …
  4. Click Add Time. …
  5. Repeat Steps 3 – 4 to compute stress analysis on other time intervals.
IT IS INTERESTING:  How do you change to dark mode in AutoCAD?

How do I load a SOLIDWORKS Simulation?

How to Use Load Cases in SOLIDWORKS Simulation

  1. Step 1: The Plan. …
  2. Step 2: Open the File. …
  3. Step 3: Create a New Static Study. …
  4. Step 4: Apply the Material as Aluminum 1060 Alloy. …
  5. Step 5: Apply Fixtures. …
  6. Step 6: Apply Loads. …
  7. Step 7: Mesh the Model. …
  8. Step 8: Open Up the Load Case Manager.

How do I run SOLIDWORKS Simulation in assembly?

How to Use Solidworks Static Simulation in an Assembly

  1. After the Add-Ins window is open, check the boxes shown below to activate the Simulation and then click OK to apply.
  2. Once the simulation is active move to the Simulation tab and click on New Study.
  3. Choose the Static simulation and then click OK (tick).

How do you show yield strength in SOLIDWORKS Simulation?

The yield strength value is displayed at the bottom of the plot legend. When checked, the local coordinate system reference triad is displayed at the lower right corner of the graphics area. The triad is displayed only for plots where you define a reference plane, axis, or coordinate system.

What types of analysis can SOLIDWORKS Simulation perform?

SOLIDWORKS Simulation Professional enables you to optimize your design, determine product mechanical resistance, product durability, topology, natural frequencies, and test heat transfer and buckling instabilities. It can also perform sequential multi-physics simulations.

Where is results and plots SOLIDWORKS?

The software generates a Results folder in the Simulation study tree after running a study successfully. The default plots in the Results folder depend on the study type and the options you set on the Default Options tab of the Options dialog box.

IT IS INTERESTING:  What's the difference between architecture and architectural technology?

How do you check deflection in SOLIDWORKS?

You can perform deflection and stress calculations on structural steel cross sections. Click Beam Calculator (Toolbox toolbar) or Toolbox > Beam Calculator . In the Beam Calculator dialog box, select a Load Type. Under Type of Calculation, select Deflection or Stress.

How do I run a fatigue study in SOLIDWORKS?

7 Steps to Perform a Fatigue Analysis in SOLIDWORKS Simulation

  1. Determine the load type during study creation.
  2. Add events.
  3. Define fatigue data.
  4. Result options.
  5. Fatigue study properties.
  6. Run the analysis.
  7. Postprocess the results.
Special Project