How do I flatten a 3d model in Solidworks?

How do I flatten a model in SolidWorks?

To flatten a body, do one:

1. In the FeatureManager design tree, select the part and click Flatten. (Sheet Metal toolbar).
2. In the cut list, right-click the body and click Flatten. .
3. In either the FeatureManager design tree or the cut list, right-click the Flat-Pattern. feature for the part and click Unsuppress. .

How do you unwrap in SolidWorks?

To add an unfold feature:

1. In a sheet metal part, click Unfold. on the Sheet Metal toolbar, or click Insert > Sheet Metal > Unfold.
2. In the graphics area, select a face that does not move as a result of the feature for Fixed face. . …
3. Select one or more bends as the Bends to unfold. …
4. Click .

How do I flatten a bend in SolidWorks?

Flattening Sheet Metal Bends

1. To flatten the entire part, if the Flat-Pattern1 feature is present, unsuppress Flat-Pattern1, or click Flatten. …
2. To flatten the entire part, if the Process-Bends1 feature is present, suppress Process-Bends1, or click Flatten. …
3. To flatten one or more individual bends, add an Unfold.

Why is surface flatten greyed out?

The reason for the “Flatten” icon being greyed out was because the sheet metal part had a “Flat Pattern” annotation view and this annotation view was active. By selecting another annotation view, the “Flatten” icon then becomes available again.

How do I flatten a pipe in Solidworks?

To do this, right-click on an interior face of the tube and click Select Tangency. The Power Select command will select a few too many faces and the faces of the bends to be flattened must be deselected by clicking on both the inner and outer faces of the bend. Finally, select Delete and Patch.

How do you flatten a curved surface in Rhino?

Flatten curves and surfaces

1. InsertLineIntoCrv. Flatten the curve segment between picked points. …
2. FlattenSrf. Project surface edges onto the construction plane to create planar curves.
3. Smash. Flatten a surface without restriction to single-directional curvature.
4. Squish. …
5. SquishBack. …
6. UnrollSrf. …
7. UnrollSrfUV. …
8. Edit curves.

How do I use the wrap feature in Solidworks?

Wrap

1. Select the sketch you want to wrap from the FeatureManager design tree. …
2. Click Wrap on the Features toolbar, or click Insert > Features > Wrap.
3. In the PropertyManager, under Wrap Type: …
4. If you select Emboss or Deboss , you can select a line, linear edge, or plane to set a Pull Direction . …
5. Click OK .

How do you flatten rolled sheet metal?

Hammer and flame: flattening sheet metal with extensive expertise and time. Hammer and flame – The art of leveling parts or sheets with this method still exists in the metal fabrication industry. This method uses a hammer to flatten the sheet metal part.

How do I change the direction of a bend in Solidworks?

Editing the Flat Pattern feature, in the Flat-Pattern folder, will display the currently defined “Fixed face”. To change the Bend Direction, select a face that is on the other side of the material. Once complete, the stated Bend Direction in the drawing, will also change.

How can you tell if a surface is flat in Solidworks?

Click Insert > Features > Move/Copy. You can use the Measure tool to check your flattened surface for accuracy. Measure the surface area of the folded and flattened features. If there is a large discrepancy between the surface areas, the flattened feature might not be accurate.

How do you project a sketch on a curved surface in Solidworks?

Click Project Curve on the Curves toolbar, or Insert > Curve > Projected. Use this selection to project a sketched curve onto a model face. Under Sketch to Project , select the curve in the graphics area or from the flyout FeatureManager design tree.