Your question: How do I extend extrusion in Solidworks?

How do you extend extrude in SolidWorks?

Extend Surface

1. Click Extended Surface (Surfaces toolbar) or Insert > Surface > Extend.
2. In the PropertyManager: Under Edges/Faces to Extend, select one or more edges or faces in the graphics area for Selected Face/Edges . For edges, the surface extends along the plane of the edge. …
3. Click .

How do you extend an extruded surface?

To extend or extrude the edge of a surface

Select the outside edge of a surface. Ctrl+click to select multiple edges. Click the Pull arrow oriented along the surface to extend the edge. Press Tab or click the other Pull arrow to extrude the edge in another direction.

How do I extend a part in SolidWorks?

Extend Entities

1. In an open sketch, click Extend Entities. on the Sketch toolbar, or click Tools > Sketch Tools > Extend. …
2. Move the pointer over the sketch entity to extend. …
3. If the preview extends in the wrong direction, move the pointer to the other half of the line or arc.
4. Click the sketch entity to accept the preview.

How do I edit extrusions in SolidWorks?

To edit the definition of a feature:

1. Do one of the following: Select a feature in the FeatureManager design tree or the graphics area. Click Edit > Definition. …
2. Edit the definition in the dialog box by specifying new values or options.
3. Click OK to accept the changes.

What is the file extension of a SOLIDWORKS drawing file?

When you save a file natively in SOLIDWORKS, it can be saved as an: SLDPRT part file (. sldprt) SLDASM assembly file (.

How do you cut extrude?

Creating Extruded or Revolved Cuts as Assembly Features

1. Open a sketch on a face or plane, and sketch a profile of the cut. …
2. Click Extruded Cut or Revolved Cut (Features toolbar), or click Insert > Assembly Feature > Cut , then Extrude or Revolve.
3. Set the options as needed in the Extrude or Revolve PropertyManager.

How do you extend extrusion in rhino?

If the extrusion is vertical use Command-Drag or Move > Vertical to constrain the point. Gumball can also help. My favourite is to command+click the extruded edge(s) , or surface if extruded solid, and pull with GumBall. You can do this but it will no longer be an extrusion object, if that matters.

How do I extend a surface in Rhino?

Steps

1. Select a boundary object, type a length, or press Enter to extend without boundary edges.
2. Select a curve or an surface edge near the end. The extension will be automatically joined with the original curve. …
3. Pick the end of the extension or type a length.

How do I extend a surface in Spaceclaim?

To extend or trim adjacent surfaces

1. Click Extend in the Analysis group of the Prepare tab. …
2. Change the following options: …
3. If you want to extend or trim only some of the surfaces or sketch curves, click the highlighted spots. …
4. Click Complete if you want to extend or trim all highlighted surfaces.

How do you move faces in Solidworks?

Found on the Direct Editing tab of the Command Manager, this simple command is in my opinion one of the most underrated tools in SOLIDWORKS. The Direct Editing tab may not be shown by default, so right-click any other tab to show it. Or, use Command Search to initiate a Move Face command.

How do you move a cut Extrude in Solidworks?

To move more than one feature at a time, hold down Ctrl as you select the features.
…
To move a feature to a new place on a model:

1. Select Instant3D (Features toolbar).
2. In the graphics area, select the feature to move.
3. Use the handles to drag the feature to its new location.

How do you undo an extrusion in Solidworks?

To remove the faces defining the extrude from the model after extruding, click Delete original faces. The green area is the face defining the extrude. The resulting model is hollow where the face was deleted. To create a single body from the extrude when faces are deleted, select Knit result .

How do you edit an Extrude?

Edit an Extrusion

1. In the drawing area, select the extrusion.
2. If you are in the project environment: …
3. Click Modify | Extrusion tab Mode panel (Edit Extrusion).
4. If desired, modify the extrusion profile.
5. On the Properties palette, change the visibility, material, or subcategory of the extrusion, if desired.