How do you read window sizes on house plans?

Read a window size listed on a set of architectural drawings. It will look similar to “3050,” which specifics the window’s dimensions. The numbers represent a window that is 3-feet 0-inches wide by 5-foot 0-inches tall. The first digit is in feet and the second digit is the inches that a window is wide.

How do you represent a window in a floor plan?

WINDOWS: Windows are shown drawn within the walls on the floor plan and are indicated by three parallel lines. They may have the window size labelled on the window or a number. A number will correspond to a number on the window schedule.

How are window sizes written?

A window’s size notation is basically width and height combined. The first two #’s are for width and the second two #’s are for height. A 2426 Replacement Window would have a width of 2’4″ and height of 2’6″.

What does WH mean on floor plan?

hot water heater

How do I make a floor plan?

There are a few basic steps to creating a floor plan:

1. Choose an area. Determine the area to be drawn. …
2. Take measurements. If the building exists, measure the walls, doors, and pertinent furniture so that the floor plan will be accurate. …
3. Draw walls. …
4. Add architectural features. …
5. Add furniture.

How do I find the floor plan for my house?

How to Get Floor Plans of an Existing House

1. Talk to the contractor that built your house, if possible. …
2. Locate the archives of the municipality or county where your house is located. …
3. Locate the fire insurance maps for the community. …
4. Visit your local building inspector’s office. …
5. Browse through historical plan books.

Are floor plans length by width?

All dimensions are always presented in feet and inches. … Room dimensions are presented in width by the length. For example, a room that has a dimension of 12′ x 16′ means it’s 12 feet wide (from side to side) by 16 feet long (from top to bottom).

What are common window sizes?

Standard sliding window widths are 36, 48, 60, 72 and 84 inches wide; the windows themselves are actually 36 1/2, 47 1/2, 59 1/2, 71 1/2 and 83 1/2 inches wide to allow for installation. Standard heights are 24 inches, 36 inches, 48 and 60 inches. A 6-foot-wide by 4-foot-tall window is identified as “6040.”

How do I determine window size?

Make three vertical measurements – on the left side of the window from the sill to the header, then the center and finally on the right side. Record the smallest of these numbers. This is the window opening height.

What is a 3 0 window?

A rough opening refers to the framed opening of a window. … Because these elements take up space, a window that measures, for example, 3 feet wide and 4 feet tall is listed as 3/0 – 4/0, but the actual window measurements will be slightly less than this to accommodate the installation system.

How do you read a basic blueprint?

4 Tips for Reading Blueprints

1. Begin with the title block. The title block is the first piece of information you’ll see in construction site plans. …
2. Study the plan legend. …
3. Find the blueprint’s scale and orientation. …
4. Look for notes from the architect.

How do plumbers read blueprints?

How to Read Plumbing Blueprints

1. Obtain a guide to the plumbing symbols on a blueprint. …
2. Spread the blueprint on a table, counter or other flat surface that will allow you to read the entire page at once. …
3. Read the schedules that accompany the blueprints. …
4. Identify the symbols for major plumbing fixtures such as sinks, showers, bathtubs and toilets.

How do you read a site plan?

Tips on How to Read a Site Plan

1. Find The Title Block. In the bottom right corner of most plans, you’ll find what’s called a title block. …
2. Learn the Plan’s Scale. …
3. Determine the Orientation of the Plan. …
4. Know the Datum Point. …
5. Note the Site’s Contours. …
6. Locate Existing Structures.

7 мая 2014 г.